Господа, доброго времени суток!
Подскажите, плиз, как прошивку залить новую на медпро...
почему-то подвисает иногда...
прошивка TN2302
Модератор: Administrator
-
Баргилов Арсентий
- ACE
- Сообщения: 417
- Зарегистрирован: Пн 27 фев 2006, 11:11
- Откуда: Ланит
- Контактная информация:
-
ppsasha
- Участник форума
- Сообщения: 61
- Зарегистрирован: Пт 23 май 2008, 09:35
- Откуда: Волгоград
- Контактная информация:
спасибо iLiya, может кто знает как решить мою проблему: У меня после грозы аналоговая плата TN 2793 b V13 при тестировании выдаёт:
тест 51-ошибка 2000, тест 220-ошибка 1018. Постоянно горит зелёный светодиод. Ставил на порт телефон - нет зуммера. вообще после грозы у меня все аналоговые платы выдают ошибку 1018. SOS!!! Помогите кто чем может.
тест 51-ошибка 2000, тест 220-ошибка 1018. Постоянно горит зелёный светодиод. Ставил на порт телефон - нет зуммера. вообще после грозы у меня все аналоговые платы выдают ошибку 1018. SOS!!! Помогите кто чем может.
Тяжела и неказиста жизнь российского связиста
-
13-ый
- ACS-Implement
- Сообщения: 575
- Зарегистрирован: Пн 05 фев 2007, 10:25
- Откуда: Москва. Небольшая конторка. Не интеграторствую.
- Контактная информация:
test 51 error 2000 ABRT
There was no response from the board.
1. If Error Type 1538 (hyperactivity) is present in the error log, follow the
maintenance strategy that is recommended for this Error Type.
2. Run busyout board location, reset board location, and
release board location, and retest.
3. If the test still aborts, dispatch with the circuit pack.
4. Check the off-board wiring and the terminal, and, if there are no
problems found, replace the circuit pack.
Test #220 Neon Test
error 1018 ABRT There are not any translated ports on the circuit pack, or if there are ports,
then none are administered to have "neon."
1. Verify that there are ports administered on the circuit pack. If no ports
are administered, no further action is required.
2. Verify that you have neon sets connected (Avaya sets that may be
neon sets are 500 and 2500 series, also some non-Avaya may also be
neon sets). If no neon sets are connected to the circuit pack, the test
continues to abort, but no further action is required.
3. If there are no neon sets connected to the circuit pack, at least one
port needs to be translated with neon. To check if a port is translated
with neon, use the display port location command to
determine the station extension of any station on this circuit pack. Use
the display station extension to determine if the port is
administered with neon. The field "Message Waiting Indicator:" must
be set to "neon" for at least one of the administered ports. If this field is
not administered to "neon" the test continues to abort. This is
acceptable because not all stations have neon lamps on their analog
terminals. If none of the terminals have neon lamps, the test continues
to abort, but no further action is required.
4. Retry the command again.
5. Retry the command at 1-minute intervals a maximum of 5 times.
6. If the test continues to abort, look for RING-GEN errors in the Error
Log. If an ABRT 1008 occurs for this test on other circuit packs as well,
then the ringing generator may be defective. If it does not occur on
port test 48 for ANL-16-L, all four ring phases are in use.
7. Retry the command again.
взято из документа Maintenance Alarms for Avaya Communication Manager 3.1, Media Gateways and Servers очень
There was no response from the board.
1. If Error Type 1538 (hyperactivity) is present in the error log, follow the
maintenance strategy that is recommended for this Error Type.
2. Run busyout board location, reset board location, and
release board location, and retest.
3. If the test still aborts, dispatch with the circuit pack.
4. Check the off-board wiring and the terminal, and, if there are no
problems found, replace the circuit pack.
Test #220 Neon Test
error 1018 ABRT There are not any translated ports on the circuit pack, or if there are ports,
then none are administered to have "neon."
1. Verify that there are ports administered on the circuit pack. If no ports
are administered, no further action is required.
2. Verify that you have neon sets connected (Avaya sets that may be
neon sets are 500 and 2500 series, also some non-Avaya may also be
neon sets). If no neon sets are connected to the circuit pack, the test
continues to abort, but no further action is required.
3. If there are no neon sets connected to the circuit pack, at least one
port needs to be translated with neon. To check if a port is translated
with neon, use the display port location command to
determine the station extension of any station on this circuit pack. Use
the display station extension to determine if the port is
administered with neon. The field "Message Waiting Indicator:" must
be set to "neon" for at least one of the administered ports. If this field is
not administered to "neon" the test continues to abort. This is
acceptable because not all stations have neon lamps on their analog
terminals. If none of the terminals have neon lamps, the test continues
to abort, but no further action is required.
4. Retry the command again.
5. Retry the command at 1-minute intervals a maximum of 5 times.
6. If the test continues to abort, look for RING-GEN errors in the Error
Log. If an ABRT 1008 occurs for this test on other circuit packs as well,
then the ringing generator may be defective. If it does not occur on
port test 48 for ANL-16-L, all four ring phases are in use.
7. Retry the command again.
взято из документа Maintenance Alarms for Avaya Communication Manager 3.1, Media Gateways and Servers очень
-
ppsasha
- Участник форума
- Сообщения: 61
- Зарегистрирован: Пт 23 май 2008, 09:35
- Откуда: Волгоград
- Контактная информация:
она уже была в ремонте по той-же причине. когда она пришла обратно наш микроэлектронщик не нашёл ни капли новой пайки, вывод-её не перепаивали значит перепрошивали. вот я и спрашивал можно-ли её перепрошить на "родной" станции ибо нах платить немалые деньги за то что и сам можешь сделать. 
Тяжела и неказиста жизнь российского связиста