Телефон Avaya 9670

[dron85]

Добрый день Уважаемые!

Появилась необходимость в настройке данной модели (9670), поиском ответов не нашел поэтому вопросы следующие:
1. как можно облегчить создание телефонной книги, т.е. латинскую qqwerety клавиатуру заменить на кириллицу, а то очень долго вводить по одной русской букве, как я понял длля телефона это просто символ.
2. Как настроить работу приложений (миировое время, погода), где это включается и настраивается.
3. Как настроить резервирование меток и контактов. Есть tftp сервеh Avaya MV_IPTel, задал настройки set bruri и set brauth , но при резервировании необходимо ввести какой то логин/пароль. Где его задать. Ведь если сохранить файл меток и контактов, то можно его потом на компе изменить и пергрузив телефон получить переведенные и переименованные метки автоматически.

Спасибо за помощь

[michael_loginov]

есть доки, в котрых много что расписано
например
http://downloads.avaya.com/css/P8/documents/100057468
касаемо 96ой серии, 9670 особо ничем не отличается от 9650, разве что цветной, болшой и сенсорный.
мой совет, забудьте про русский. криво все это у аваии на оконечном оборудовании.

[gosha]

У 9670 одна проблема - нету русских букв на клавиатуре. Во всем остальном - дока на 9600

[michael_loginov]

У 9670 одна проблема - нету русских букв на клавиатуре. Во всем остальном - дока на 9600

смотря что понимать под отсутствием, вприцнипе оно есть, но через опу и не очень удобно. если только прошивку аваевскую как то вскрыть изменитьи запаковать обратно

[dron85]

У 9670 одна проблема - нету русских букв на клавиатуре. Во всем остальном - дока на 9600

смотря что понимать под отсутствием, вприцнипе оно есть, но через опу и не очень удобно. если только прошивку аваевскую как то вскрыть изменитьи запаковать обратно

вот поэтому и хочется проделать переименование меток через backup/restore.
текст файла 46ххsettings.txt:
(кое что выкинул из файла, прикрепить не получается)
################## HTTP SERVER SETTINGS ##################
##
## HTTP Server Addresses
## [If you set your HTTP Server Addresses via DHCP, do not
## set them here as they will over ride your DHCP settings.
## Also, use TLSSRVR instead if you require an
## authenticated server]
## Server used to down load configuration script files.
## Zero or more HTTP server IP addresses in dotted-decimal
## or DNS name format, separated by commas without any
## intervening spaces. (0 to 255 ASCII characters,
## including commas).
SET HTTPSRVR 198.152.254.2
##
## Server Authentication
## Sets whether script files are downloaded from an
## authenticated server over an HTTPS link.
## 0 for optional, 1 for mandatory
## SET AUTH 0
##
################ DOMAIN NAME SYSTEM (DNS) ################
##
## If you set your DNS parameters via DHCP, do not set them
## here as they will over ride your DHCP settings.
##
## Your Domain Name Server
## SET DNSSRVR 198.152.15.15
##
## Your DNS domain
## SET DOMAIN mycompany.com
##
##
############# CALL SERVER ADDRESS OVERRIDE ###############
##
## STATIC specifies whether a call server IP address that
## has been manually programmed into the phone may override
## any value received via DHCP or this settings file.
## 0 for disabled, 2 for override
##
## SET STATIC 0
##
################# DHCP ADDRESS SETTINGS ##################
##
## DHCPSTD controls whether the phone continues to use an
## expired IP address if the phone received no response to
## its address renewal request. 0 for yes, 1 for no.
##
SET DHCPSTD 1
##
## VLANTEST specifies the number of seconds to wait for a
## DHCPOFFER when the phone is using a non-zero VLAN ID.
## (0-999)
##
SET VLANTEST 0
##
############# ENHANCED LOCAL DIALING RULES ###############
##
## These settings affect certain dialing behaviors, such as
## dialing numbers from the incoming Call Log or from web
## pages
##
## Dialing Algorithm Status
## Controls whether algorithm defined by parameters in
## this section is used during certain dialing behaviors.
## 1 enables the algorithm, 0 disables the algorithm.
SET ENHDIALSTAT 1
##
## Country Code
## For United States the value is '1'
## SET PHNCC 1
##
## Internal extension number length
## If your extension is 12345, your dial plan length is 5.
## On 46xx phones, the maximum extension length is 10.
## On 96xx phones, the maximum extension length is 13.
## This value must match the extension length set on your
## call server.
SET PHNDPLENGTH 4
##
## International access code
## For the United States, the value is 011.
## SET PHNIC 011
##
## Long distance access code
SET PHNLD 8
##
## National telephone number Length
## For example, 800-555-1111 has a length of 10.
SET PHNLDLENGTH 10
##
## Outside line access code
## The number you press to make an outside call.
SET PHNOL 9
##
##
############## APPLICATION ACCESS SETTINGS ###############
##
## These settings restrict access to certain applications.
##
## When APPSTAT is set to 0, Call Log and Redial are
## suppressed and changes to Speed Dial/Contacts are not allowed.
##
## When APPSTAT is set to 1, Call Log, Redial and,
## Speed Dial/Contacts work without restrictions.
##
## When APPSTAT is set to 2, Call Log is suppressed.
## For Redial the Last-6-numbers option is suppressed
## and changes to Speed Dial/Contacts are not allowed.
##
## When APPSTAT is set to 3, changes to Speed Dial/Contacts
## are not allowed.
##
## SET APPSTAT 1
##
##
################# OPTION ACCESS SETTINGS #################
##
## This setting restricts access to certain user options.
##
## When OPSTAT is set to 000, the user options
## are not accessible.
##
## When OPSTAT is set to 001, the user can only access
## the Log-Off Option.
##
## When OPSTAT is set to 010, the user can only access
## view-only options. The user cannot change any setting.
##
## When OPSTAT is set to 011, the user can only access
## view-only options and the Log-Off Option.
##
## When OPSTAT is set to 100, the user can access
## all options except the view-only options and
## the Log-Off option.
##
## When OPSTAT is set to 101, the user can access
## all options except the view-only options.
##
## When OPSTAT is set to 110, the user can access
## all the options except the Log-Off option.
##
## When OPSTAT is set to 111, the user can invoke
## any or all of the user options.
##
## SET OPSTAT 111
##
##
############# LOCAL PROCEDURE ACCESS SETTINGS ############
##
## Restrict Local Procedure Access
## Controls whether local (dial pad) procedures can be
## used to administer the telephone.
## 0 means local procedures can be accessed from the
## telephone.
## 1 means local procedures can not be accessed from the
## telephone.
## CAUTION:Be absolutely sure before setting PROCSTAT to 1
## SET PROCSTAT 0
##
## Local Procedure Password
## Sets password for local (dial pad) procedure access.
## (1 to 7 ASCII numeric digits). See your telephone's
## Administrator's guide for the default password
## supported by your release.
## SET PROCPSWD 9999
##
#################### AUDIO SETTINGS ######################
##
## Automatic Gain Control (AGC).
## These settings enable or disable AGC.
##
## A value of 1 enables AGC. A value of 0 disables AGC.
## AGCHAND controls handset AGC
## AGCHEAD controls headset AGC
## AGCSPKR controls speaker AGC
##
## SET AGCHAND 1
## SET AGCHEAD 1
## SET AGCSPKR 1
##
## Headset Operational Mode
## Controls whether the headset ignores a disconnect
## message.
##
## A value of 0 or 2 makes the headset go on-hook when it
## receives a disconnect message.
## A value of 1 or 3 makes the headset ignore a disconnect
## message.
##
## SET HEADSYS 1
##
## Audio Environment Index
## Enables you to customize the telephone's audio
## performance. (0-107) This parameter affects settings
## for AGC dynamic range, handset and headset expansion
## thresholds, and transmit gain. It is highly recommended
## you consult Avaya before changing this parameter.
##
## SET AUDIOENV 0
##
##
################# WML BROWSER SETTINGS ###################
##
## This section contains the common settings used to
## enable and administer the 'Web' application.
##
## The settings 'WMLHOME', which sets the URL of the
## telephone home page, and 'WMLIDLEURI', which sets the
## idle phone home page, may be different for each set
## type to take advantage of the capabilities of the
## individual sets. WMLHOME and WMLIDLEURI should be set
## in the sections for the individual set types.
## Note: The 9610 does not use WMLHOME or WMLIDLEURI.
## Use WMLSMALL in their place.
##
## Your HTTP proxy server address (name or IP address)
## SET WMLPROXY my.proxy.company.com
##
## The TCP port number of your HTTP proxy server
## SET WMLPORT 8080
##
## A list of one or more HTTP proxy server exception
## domains separated by commas without any spaces.
## Accesses to these addresses will not go through the
## proxy server.
## SET WMLEXCEPT mycompany.com,135.20.21.20
##
## The idle period in minutes before the WMLIDLEURI
## web page is displayed. Valid values are 1 to 999.
## Default (if WMLIDLEURI is set) is 10 minutes.
## SET WMLIDLETIME 100
##
##
################ PUSH INTERFACE SETTINGS #################
##
## These settings are used to administer the Push interface
##
## The list of all the Trusted Push Servers.
## If set to "/", all servers are allowed.
## If set to null or blank, Push is disabled.
## SET TPSLIST 135.20.21.20
SET TPSLIST /
##
## The list of all the Subscription Servers.
## SET SUBSCRIBELIST http://135.20.21.21/subscribe
##
## The TCP port number for the telephone's HTTP server.
## (80-65535). The default is 80.
SET PUSHPORT 80
##
## Push capabilities settings. PUSHCAP consists of 3 bits
## (each 0, 1, or 2). The rightmost bit controls the Top
## Line push mode. The middle bit controls the Web
## Browser push mode. The leftmost bit controls the Audio
## push mode.
##
## When PUSHCAP is set to 000, all push modes are disabled
##
## When PUSHCAP is set to 111, barge in only is allowed in
## all push modes.
##
## When PUSHCAP is set to 222, both barge in and normal
## pushes are allowed in all push modes.
SET PUSHCAP 111
##
##
#################### RTCP MONITORING #####################
##
## The RTCP monitor
## One RTCP monitor (VMM server) IP address in
## dotted-decimal format or DNS name format (0 to 15
## characters). Note that for H.323 telephones only this
## parameter may be changed via signaling from Avaya
## Communication Manager.
## SET RTCPMON 192.168.0.10
##
## RTCPMONPORT sets the port used to send RTCP information
## to the IP address specified in the RTCPMON parameter.
## RTCPMONPORT is only supported on SIP telephones.
## The default is 5005.
##
## SET RTCPMONPORT "5005"
##
########### CONVERGED NETWORK ANALYZER SETTINGS ##########
##
## The CNA server
## One or more CNA server IP addresses in
## dotted-decimal format or DNS name format (0 to 255
## characters).
## SET CNASRVR 192.168.0.10
##
## CNA port
## Sets the port used for CNA registration. (0-65535)
## The default is 50002.
## SET CNAPORT 50002
##
##
################## ETHERNET INTERFACES ###################
##
## Primary Interface Status
## Controls the speed and duplex settings for the primary
## Ethernet interface.
## 1 for auto-negotiate
## 2 for 10Mbps half-duplex
## 3 for 10Mbps full-duplex
## 4 for 100Mbps half-duplex
## 5 for 100Mbps full-duplex
## 6 for 1Gbps full-duplex (96xx phones only)
SET PHY1STAT 1
##
## PC Interface Status
## Controls the speed and duplex settings for the PC
## Ethernet interface.
## 0 for disabled
## 1 for auto-negotiate
## 2 for 10Mbps half-duplex
## 3 for 10Mbps full-duplex
## 4 for 100Mbps half-duplex
## 5 for 100Mbps full-duplex
## 6 for 1Gbps full-duplex (96xx phones only)
## SET PHY2STAT 1
##
################## 802.1P/Q SETTINGS ###################
##
## Telephone Frame Tagging
## Controls whether layer 2 frames generated by the
## telephone have IEEE 802.1Q tags.
## 0 for Auto, 1 for On, and 2 for Off
## For H.323 phones, this parameter may also be changed
## via LLDP.
## SET L2Q 0
##
## VLAN Separation
## Controls whether layer 2 frames to/from the telephone's
## secondary Ethernet interface have their 802.1Q tags
## changed. 0 for do not change tags, 1 for change tags.
## SET VLANSEP 0
##
## Voice VLAN Identifier
## VLAN identifier to be used by IP telephones. This
## parameter should only be set when IP telephones are to
## use a VLAN that is separate from the default data VLAN.
## If the VLAN identifier is to be configured via H.323
## signaling based on Avaya Communication Manager
## administration forms, it should not be set here.
## For H.323 phones, this parameter may also be changed
## via LLDP.
SET L2QVLAN 198
##
## Secondary Ethernet Interface VLAN Identifier
## VLAN Identifier to be used for frames to/from the
## telephone's secondary Ethernet interface. (0-4094)
## This parameter should only be set if VLANSEP is 1.
## For H.323 phones, this parameter may also be changed
## via LLDP.
## SET PHY2VLAN 0
##
## Audio Priority Value
## Sets the layer 2 priority value for audio packets
## from the phone. (0-7)
## For H.323 phones, this parameter may also be
## changed from Communication Manager.
## SET L2QAUD 6
##
## Signaling Priority Value
## Sets the layer 2 priority value for signaling
## protocol messages from the phone. (0-7)
## For H.323 phones, this parameter may also be
## changed from Communication Manager.
## SET L2QSIG 6
##
## Secondary Ethernet Interface Priority Value
## Sets the priority value for layer 2 frames to/from
## the telephone's secondary Ethernet interface. (0-7)
## This parameter should only be set if VLANSEP is 1.
## SET PHY2PRIO 0
##
##################### SNMP SETTINGS ######################
##
## SNMP addresses
## If this parameter is set, an SNMP query will only be
## accepted if the source IP address of the query matches
## one of these values. This parameter may contain one or
## more IP addresses in dotted-decimal or DNS name format,
## separated by commas without any intervening spaces
## (0 to 255 ASCII characters, including commas).
## SET SNMPADD 192.168.0.22,192.168.0.23
##
## SNMP community name string
## This value must be set to enable viewing of the phone's
## MIB. This value must match the community string name
## used in the SNMP query (up to 32 ASCII characters, no
## spaces).
## SET SNMPSTRING mystring
##
##
################ EVENT LOGGING SETTINGS ##################
##
## Event Logging control
## Controls the level of events logged in the
## endptRecentLog and endptResetLog objects in the SNMP
## MIB. Events with the selected severity level and higher
## will be logged.
## 0 for disabled
## 1 for emergencies
## 2 for alerts
## 3 for critical
## 4 for errors
## 5 for warnings
## 6 for notices
## 7 for information
## 8 for debug
## SET LOGLOCAL 5
##
## Syslog Server address
## One syslog server IP address in dotted-decimal or DNS
## name format (0 to 255 ASCII characters).
## SET LOGSRVR 192.168.0.15
##
##
############### DISPLAY BACKLIGHT CONTROL ################
##
## Idle Time Before Turning Off Backlight (minutes)
## Number of minutes without phone activity to wait
## before turning off backlight. A value of 0 means the
## backlight is never turned off. This parameter is
## supported only by phones which have a backlight.
## The default is 120 minutes.
## SET BAKLIGHTOFF 120
##
##
##################### 802.1X SETTINGS ####################
##
## This setting determines the 802.1X operating mode
## 0: Unicast Supplicant operation only, with PAE
## multicast pass-through.
## No proxy Logoff. DEFAULT OPERATION.
## 1: Same operation as for "0" but with proxy Logoff.
## 2: Unicast or multicast Supplicant operation.
## No PAE multicast pass-through or proxy Logoff.
## SET DOT1X 0
##
##
###################### ICMP SETTINGS #####################
##
## Destination Unreachable Message Control
## Controls whether ICMP Destination Unreachable messages
## are generated.
## 0 for No
## 1 for limited Port Unreachable messages
## 2 for Protocol and Port Unreachable messages
## SET ICMPDU 1
##
## Redirect Message control
## Controls whether received ICMP Redirect messages will
## be processed
## 0 for No
## 1 for Yes
## SET ICMPRED 0
##
##

###### 46xx Automatic Backup/Restore Settings ########
##
## RESTORESTAT enables/disables the automatic backup and
## restore of user data. Applies to both FTP and HTTP
## backup/restore. This setting does not apply to the
## 4602 sets.
##
## A value of 1 enables Backup/Restore.
## A value of 0 disables Backup/Restore.
##
## FTPUSERSTAT sets user permissions on modifications to
## server names and directory paths used for FTP
## backup/restore. Does not apply to HTTP backup/restore.
##
## When FTPUSERSTAT is set to 0, the user can only use the
## server and path data administered via DHCP or settings
## file.
##
## When FTPUSERSTAT is set to 1, the user can specify
## alternative FTP servers or directory paths. The default
## is 1.
##
## When FTPUSERSTAT is set to 2, the user can specify
## alternative FTP directory paths but is not allowed to
## specify alternative FTP servers.
##
## FTPSRVR specifies the IP Address of the default FTP
## Server. May be a dotted-decimal address or DNS string.
## Depending on FTPUSERSTAT setting, may be overridden by
## the user.
##
## FTPDIR specifies the default directory path used for
## storage and retrieval of phone user information.
## Depending on FTPUSERSTAT setting, may be overridden by
## the user.
##
##SET RESTORESTAT 1
##SET FTPUSERSTAT 1
##SET FTPSRVR 198.152.254.2
##SET FTPDIR C:\Program Files\Avaya\MV_IPTel\data\Backup\
##
#################### LOGIN SETTINGS ######################
##
## QKLOGINSTAT specifies whether a password must always be
## entered manually at the login screen.
##
## A value of 0 makes manual password entry mandatory.
## A value of 1 enables a "quick login' by pressing the
## # key to accept the current password value.
##
## SET QKLOGINSTAT 1
##
##
############################################################
## ##
## 96xx SETTINGS ##
## Settings applicable to 96xx telephone models ##
## ##
############################################################
##
## Voice Mail Telephone Number
## Specifies the telephone number to be dialed
## automatically when the telephone user presses the
## Messaging button. The specified number is used to
## connect to the user’s Voice Mail system.
## SET MSGNUM 1234
##
##
## HTTP Server Directory Path
## Specifies the path name to prepend to all file names
## used in HTTP and HTTPS GET operations during startup.
## (0 to 127 ASCII characters, no spaces.)
SET HTTPDIR /
##
###### 96XX IP Phone Multi-Language Administration #######
##
## These settings are used to set the local display
## language of your 96XX telephone.
##
## English Language Selection Status
## Specifies whether built-in English language text strings
## are selectable by the user. 0 for off, 1 for on.
SET LANG0STAT 1
##
## First Language File Name
## Contains the name of the first language file.
## 0 to 32 ASCII characters. File name must end in .txt
##
## Note:
## It is recommended you install the latest version of the
## language files in all 96xx telephones, even if some
## phones are running an earlier release of software.
##
SET LANG1FILE "mlf_S31_v51_russian.txt"
##
## Second Language File Name
## Contains the name of the second language file.
## 0 to 32 ASCII characters. File name must end in .txt
## SET LANG2FILE "mlf_s12_v10_spanish.txt"
##
## Third Language File Name
## Contains the name of the third language file.
## 0 to 32 ASCII characters. File name must end in .txt
## SET LANG3FILE "mlf_s12_v10_french_paris.txt"
##
## Fourth Language File Name
## Contains the name of the fourth language file.
## 0 to 32 ASCII characters. File name must end in .txt
## SET LANG4FILE "mlf_s12_v10_german.txt"
##
## System-Wide Language
## Contains the name of the default system language file.
## 0 to 32 ASCII characters. File name must end in .txt
## SET LANGSYS "mlf_s12_v10_german.txt"
##
################ Larger Text Font SETTINGS #################
##
## Larger Text Font File name
## Specifies the loadable language file on the HTTP server
## for the Large Text Font. 0 to 32 ASCII characters.
##
## SET LANGLARGEFONT "mlf_s12_v10_english_large.txt"
##
################## BACKUP/RESTORE SETTINGS #################
##
## Backup and Restore URI
## URI used for HTTP backup and retrieval of user data.
## Specify HTTP server and directory path to backup file.
## Do not specify backup file name.
SET BRURI http://198.152.254.2/PhoneBackup
SET BRAUTH 0
##
############## AUDIBLE ALERTING ##################
##
## Specifies the audible alerting setting for the telephone
## and whether users may change this setting.
##
## A value of 0 turns off audible alerting; user cannot
## adjust ringer volume at all.
## A value of 1 turns on audible alerting; user can adjust
## ringer volume but cannot turn off audible alerting.
## A value of 2 turns off audible alerting; user can adjust
## ringer volume and can turn off audible alerting.
## A value of 3 turns on audible alerting; user can adjust
## ringer volume and can turn off audible alerting.
## The default value is 3.
##
## SET AUDASYS 3
##
##
################ AVAYA SCREEN SAVER SETTINGS ###################
##
## Idle time before the Avaya Screen Saver is activated (minutes).
## Number of minutes without phone activity to wait
## before the screen saver is activated. A value of 0 means
## the screen saver is never activated.
## The default is 240 minutes.
##
## Note:
## This setting activates the Avaya Screen Saver which is
## different than the "idle screen" accessed by WMLIDLEURI.
## While it is possible to use WMLIDLEURI as an "idle
## screen", it is recommended that the SCREENSAVERON
## timer and the Avaya Screen Saver display be used for
## screen saver purposes.
SET SCREENSAVER logo.jpg
SET SCREENSAVERON 5
##
################ A(Avaya) Menu Settings #################
##
## WML-Application URI
## URI used for WML-applications under A (AVAYA) Menu.
## Specify HTTP server and directory path to administration
## file (AvayaMenuAdmin.txt). Do not specify the
## administration file name.
##
## SET AMADMIN http://192.168.0.28
##
############################################################
## ##
## H.323 SETTINGS ##
## Settings specific to telephones with H.323 software ##
## ##
############################################################
##
## The Call Server Addresses
## [If you set your Call Server Addresses via DHCP, do not
## set them here as they will over ride your DHCP settings.]
## One or more Avaya Communication Manager server IP
## addresses in dotted-decimal or DNS name format,
## separated by commas without any intervening spaces
## (0 to 255 ASCII characters, including commas).
## SET MCIPADD 192.168.0.5
##
## Unnamed Registration Status
## Specifies whether unnamed registration is initiated if
## a user fails to enter a value at the Extension prompt.
## Unnamed registration provides the telephone with
## TTI-level service, enabling a user, for example, to
## dial emergency services such as 911.
## SET UNNAMEDSTAT 1
##
## Reregistration Timer
## Controls an H.323 protocol timer. It is highly
## recommended you consult Avaya before changing this
## parameter.
## SET REREGISTER 20
##
## CTI Status
## Controls the status of the Computer-Telephony Interface.
## 0 for disabled, 1 for enabled
## SET CTISTAT 0
##
## CTI Port
## Sets the UDP port number for reception of broadcast
## CTI discovery messages. (49714-49721).
## SET CTIUDPPORT 49721
##

## ##
## PER MODEL SETTINGS ##
## Applies to specific telephone models ##
## ##
############################################################
##
IF $MODEL4 SEQ 4601 GOTO SETTINGS4601
IF $MODEL4 SEQ 4602 GOTO SETTINGS4602
IF $MODEL4 SEQ 4610 GOTO SETTINGS4610
IF $MODEL4 SEQ 4620 GOTO SETTINGS4620
IF $MODEL4 SEQ 4621 GOTO SETTINGS4621
IF $MODEL4 SEQ 4622 GOTO SETTINGS4622
IF $MODEL4 SEQ 4625 GOTO SETTINGS4625
IF $MODEL4 SEQ 4630 GOTO SETTINGS4630
IF $MODEL4 SEQ 9610 GOTO SETTINGS9610
IF $MODEL4 SEQ 9620 GOTO SETTINGS9620
IF $MODEL4 SEQ 9630 GOTO SETTINGS9630
IF $MODEL4 SEQ 9640 GOTO SETTINGS9640
IF $MODEL4 SEQ 9650 GOTO SETTINGS9650
GOTO END
##
############################################################

############################################################
#
# SETTINGS4601
#
############################################################
##
## This section contains the phone model specific settings
## for the 4610 telephone.
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
##
GOTO END
############## END OF 4601 IP Phone Settings ###############

############################################################
#
# SETTINGS4602
#
############################################################
##
## This section contains the phone model specific settings
## for the 4602 telephone.
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
##
GOTO END
############## END OF 4602 IP Phone Settings ###############

############################################################
#
# SETTINGS4610
#
############################################################
##
## This section contains the phone model specific settings
## for the 4610 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## The WMLIDLEURI setting acts as an idle screen when the
## phone has been idle (see WMLIDLETIME value). By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTE:
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://support.avaya.com/elmodocs2/avay ... 0/idle.wml
##
GOTO END
############## END OF 4610 IP Phone Settings ###############

############################################################
#
# SETTINGS4620
#
############################################################
##
## This section contains the phone model specific settings
## for the 4620 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## The WMLIDLEURI setting acts as an idle screen when the
## phone has been idle (see WMLIDLETIME value). By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTE:
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://support.avaya.com/elmodocs2/avay ... 0/idle.wml
##
GOTO END
############## END OF 4620 IP Phone Settings ###############


############################################################
#
# SETTINGS4621
#
############################################################
##
## This section contains the phone model specific settings
## for the 4621 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## The WMLIDLEURI setting acts as an idle screen when the
## phone has been idle (see WMLIDLETIME value). By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTE:
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://support.avaya.com/elmodocs2/avay ... 0/idle.wml
##
GOTO END
############## END OF 4621 IP Phone Settings ###############

############################################################
#
# SETTINGS4622
#
############################################################
##
## This section contains the phone model specific settings
## for the 4622 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHD 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## The WMLIDLEURI setting acts as an idle screen when the
## phone has been idle (see WMLIDLETIME value). By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTE:
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://support.avaya.com/elmodocs2/avay ... 0/idle.wml
##
GOTO END
############## END OF 4622 IP Phone Settings ###############

############################################################
#
# SETTINGS4625
#
############################################################
##
## This section contains the phone model specific settings
## for the 4625 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## A value of 1 sets the sidetone level 11dB below nominal.
## A value of 2 removes all sidetone.
## A value of 0 does not change the sidetone level.
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## The WMLIDLEURI setting acts as an idle screen when the
## phone has been idle (see WMLIDLETIME value). By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTE:
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 5/home.wml
## SET WMLIDLEURI http://support.avaya.com/elmodocs2/avay ... 5/idle.wml
##
GOTO END
############## END OF 4625 IP Phone Settings ###############

############################################################
#
# SETTINGS4630
#
############################################################
##
###### Settings for the 4630 IP Phone LDAP Application #####
##
## These settings are used to enable and administer the LDAP
## application on the 4630.
##
## Your LDAP Directory server Address
## You must set this value to a non-null value to enable
## the LDAP application.
## The default is null ("") but valid values are zero or
## more IP addresses in dotted-decimal or DNS format,
## separated by commas without intervening spaces, to a
## maximum of 255 ASCII characters.##
## SET DIRSRVR ldap.mycompany.com
##
## The TCP port number of your LDAP Directory Server
## The default port number is 389. If you wish to change
## the port number, you must set this value.##
## SET DIRLDAPPORT 389
##
## The Directory Topmost Distinguished Name
## You must set this value to a non-null value to enable
## the LDAP application. The default is null ("") but
## you should set DIRTOPDN to the LDAP root entry.
## SET DIRTOPDN "People"
##
## The default LDAP search value.
## The 4630 only supports searches on names. The default
## is "cn" which stands for "complete name" in LDAP.
## CHANGING ## THIS VALUE IS NOT RECOMMENDED unless your
## LDAP directory uses a different term for this data
## field.
## SET DIRFULLNAME cn
##
## The Directory Telephone Number field.
## The default is "telephonenumber". CHANGING THIS VALUE
## IS NOT RECOMMENDED unless your LDAP directory uses a
## different term for this data field.
## SET DIRTELNUM telephonenumber
##
##
######## Settings for 4630 IP Phone Web Application ########
##
## These settings are used to enable and administer the Web
## application on the 4630.
##
## NOTE: Avaya hosts a web site for the 4630 IP Phone.
## The WEBHOME and WEBCODING parameters are set up
## to point your 4630 IP telephones to this hosted site.
## To enable this operation, remove "##" from the front
## of the lines SET WEBHOME ... (and you may need to
## administer WEBPROXY as well).
## To change the web site that your phones point to,
## remove "##" from the front of the lines SET WEBHOME ...
## and replace the provided URL with the URL of your site.
##
## NOTE: Your network must be using Domain Name Services
## (DNS) for the Avaya hosted site settings to operate
## properly.
##
## The URL of your 4630 Home page
## The default is null ("") but you can specify any other
## valid URL up to 255 characters in length.
## SET WEBHOME http://support.avaya.com/elmodocs2/avay ... /index.htm
##
## Your HTTP proxy server address (name or IP address)
## This text string contains zero or one IP address in
## dotted-decimal or DNS format, identifying an HTTP Proxy
## Server. The default is null ("") and you may not need
## to set this parameter if all Web pages to be viewed by
## the phone user are on your organization's intranet.
## SET WEBPROXY my.proxy.company.com
##
## The TCP port number of your HTTP proxy server
## The default is 80, but WEBPORT is ignored if WEBPROXY
## is null.
## SET WEBPORT 80
##
## A list of one or more HTTP proxy server exception
## domains. Accesses to these addresses will not go
## through the proxy server. The default is null ("")
## but valid values are zero or more IP addresses in
## dotted-decimal or DNS format, separated by commas
## without intervening spaces, to a maximum of 255 ASCII
## characters.
## SET WEBEXCEPT mycompany.com,135.20.21.20
##
############### 4630 Emergency Contact Number ##############
##
## If set, this number will be the top-leftmost speed dial
## button in Group 1 of the 4630 speed dial screen and
## labeled "EMERGENCY". The default is null ("") but any
## valid phone number is acceptable.
## SET PHNEMERGNUM 911
##
#################### 4630 Stock Ticker #####################
## Use this setting to activate the stock ticker on your
## 4630. Go to Options on your 4630 to complete setup of
## this feature.
## Use 0 to Disable or 1 to Enable (the default)
## SET STKSTAT 1
##
GOTO END
############## END OF 4630 IP Phone Settings ###############

############################################################
#
# SETTINGS9610
#
############################################################
##
## This section contains the phone model specific settings
## for the 9610 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## setting value
## 0 16dB (default sidetone level)
## 1 18dB
## 2 20.5dB
## 3 21dB
## 4 23.8dB (lowest value, inaudible)
## 5 13dB (loud)
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLSMALL setting is used to enable and
## administer the 'Web' Application.
##
## NOTES:
##
## The model 9610 is different from other 96xx phone
## models and does not use either WMLHOME or
## WMLIDLEURI. Use WMLSMALL in their place together
## with WMLIDLETIME. The 9610 requires the 9610 backup
## restore file to populate the home page on the phone.
## When the 9610 has been idle for WMLIDLETIME minutes,
## there are several possible displays which may appear
## depending on the values of IDLEAPP (in the 9610
## backup restore file) and WMLSMALL itself. While it is
## possible to use one of these screens as an "idle
## screen", it is recommended that the SCREENSAVERON timer
## and the Avaya Screen Saver display be used for
## screen saver purposes. See your telephone's
## Administrators guide for more information.
##
## To change the web site that your 9610 points to, remove
## the "## " from the SET WMLSMALL line and replace the
## provided URL in the line with the URL of your site.
## If WMLSMALL is null, 9610 backup-restore Main Menu WML
## links will not display
##
## SET WMLSMALL http://www.mycompany.com/my_screen.wml
##
GOTO END
############## END OF 9610 IP Phone Settings ###############

############################################################
#
# SETTINGS9620
#
############################################################
##
## This section contains the phone model specific settings
## for the 9620 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## setting value
## 0 15.1dB (default sidetone level)
## 1 17.2dB
## 2 25.4dB (lowest value,inaudible)
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## setting value
## 0 16dB (default sidetone level)
## 1 18dB
## 2 20.5dB
## 3 21dB
## 4 23.8dB (lowest value, inaudible)
## 5 13dB (loud)
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## WMLIDLEURI may be used as an "idle screen" when the
## phone has been idle for WMLIDLETIME minutes. By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTES:
##
## The WMLIDELURI idle screen is different than the
## Avaya screen saver activated by the SCREENSAVERON
## timer. While it is possible to use WMLIDLEURI as an
## "idle screen", it is recommended that the SCREENSAVERON
## timer and the Avaya Screen Saver display be used for
## screen saver purposes.
##
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://www.mycompany.com/my_screen.wml
##
GOTO END
############## END OF 9620 IP Phone Settings ###############

############################################################
#
# SETTINGS9630
#
############################################################
##
## This section contains the phone model specific settings
## for the 9630 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## setting value
## 0 15.1dB (default sidetone level)
## 1 17.2dB
## 2 25.4dB (lowest value,inaudible)
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## setting value
## 0 16dB (default sidetone level)
## 1 18dB
## 2 20.5dB
## 3 21dB
## 4 23.8dB (lowest value, inaudible)
## 5 13dB (loud)
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## WMLIDLEURI may be used as an "idle screen" when the
## phone has been idle for WMLIDLETIME minutes. By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTES:
##
## The WMLIDELURI idle screen is different than the
## Avaya screen saver activated by the SCREENSAVERON
## timer. While it is possible to use WMLIDLEURI as an
## "idle screen", it is recommended that the SCREENSAVERON
## timer and the Avaya Screen Saver display be used for
## screen saver purposes.
##
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://www.mycompany.com/my_screen.wml
##
GOTO END
############## END OF 9630 IP Phone Settings ###############
##
############################################################
#
# SETTINGS9640
#
############################################################
##
## This section contains the phone model specific settings
## for the 9640 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## setting value
## 0 15.1dB (default sidetone level)
## 1 17.2dB
## 2 25.4dB (lowest value,inaudible)
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## setting value
## 0 16dB (default sidetone level)
## 1 18dB
## 2 20.5dB
## 3 21dB
## 4 23.8dB (lowest value, inaudible)
## 5 13dB (loud)
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## WMLIDLEURI may be used as an "idle screen" when the
## phone has been idle for WMLIDLETIME minutes. By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTES:
##
## The WMLIDELURI idle screen is different than the
## Avaya screen saver activated by the SCREENSAVERON
## timer. While it is possible to use WMLIDLEURI as an
## "idle screen", it is recommended that the SCREENSAVERON
## timer and the Avaya Screen Saver display be used for
## screen saver purposes.
##
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://www.mycompany.com/my_screen.wml
##
GOTO END
############## END OF 9640 IP Phone Settings ###############
##
############################################################
#
# SETTINGS9650
#
############################################################
##
## This section contains the phone model specific settings
## for the 9650 telephone.
##
##################### AUDIO SETTINGS #####################
##
## Headset Sidetone
## Controls the level of sidetone in the headset.
##
## setting value
## 0 15.1dB (default sidetone level)
## 1 17.2dB
## 2 25.4dB (lowest value,inaudible)
##
## SET AUDIOSTHD 0
##
## Handset Sidetone
## Controls the level of sidetone in the handset.
##
## setting value
## 0 16dB (default sidetone level)
## 1 18dB
## 2 20.5dB
## 3 21dB
## 4 23.8dB (lowest value, inaudible)
## 5 13dB (loud)
##
## SET AUDIOSTHS 0
##
################# WML BROWSER SETTINGS ##################
##
## The WMLHOME setting is used to enable and
## administer the 'Web' Application.
##
## WMLIDLEURI may be used as an "idle screen" when the
## phone has been idle for WMLIDLETIME minutes. By default
## this URL is NULL ("") and this screen is not activated.
##
## NOTES:
##
## The WMLIDELURI idle screen is different than the
## Avaya screen saver activated by the SCREENSAVERON
## timer. While it is possible to use WMLIDLEURI as an
## "idle screen", it is recommended that the SCREENSAVERON
## timer and the Avaya Screen Saver display be used for
## screen saver purposes.
##
## Avaya hosts a web site for IP Phones.
## The WMLHOME and WMLIDLEURI parameters are set up
## to point your IP telephones to this hosted site.
## To enable access to this site, remove the "## "
## from the SET WMLHOME ... and SET WMLIDLEURI ... lines.
## To change the web site that your phones point to,
## replace the provided URL in the SET WMLHOME .. and
## SET WMLIDELURI ...lines with the URL of your site.
##
## SET WMLHOME http://support.avaya.com/elmodocs2/avay ... 0/home.wml
## SET WMLIDLEURI http://www.mycompany.com/my_screen.wml
##
GOTO END

[michael_loginov]

phonebackup пропишите вместо PhoneBackup, да и директория эта есть в разделе Data/HTTPSData ?

[dron85]

phonebackup пропишите вместо PhoneBackup, да и директория эта есть в разделе Data/HTTPSData ?

поменял название, директория в разделе есть.

Может что то не настроено на в самом ip_MV tel?

[michael_loginov]

phonebackup пропишите вместо PhoneBackup, да и директория эта есть в разделе Data/HTTPSData ?

поменял название, директория в разделе есть.

Может что то не настроено на в самом ip_MV tel?

а что настроено то? там всего одно окно с настройками. да и дока даже к этой проге есть.

[dron85]

Не работают web приложения на 9670. Прописал прокси, порт указал. Телефон соединился с инетом, задал город в приложениях погоды и мирового времени, и пишет место не распознано на строке обновлено восклицательный знак в треугольнике.

В чем может быть проблема?

[michael_loginov]

Не работают web приложения на 9670. Прописал прокси, порт указал. Телефон соединился с инетом, задал город в приложениях погоды и мирового времени, и пишет место не распознано на строке обновлено восклицательный знак в треугольнике.

В чем может быть проблема?

я так понимаю вводили location кириллицей?

[dron85]

Не работают web приложения на 9670. Прописал прокси, порт указал. Телефон соединился с инетом, задал город в приложениях погоды и мирового времени, и пишет место не распознано на строке обновлено восклицательный знак в треугольнике.

В чем может быть проблема?

я так понимаю вводили location кириллицей?

нет латинницей, причем при проверке города в приложении пишется "Kovrov Russia"

[michael_loginov]

Не работают web приложения на 9670. Прописал прокси, порт указал. Телефон соединился с инетом, задал город в приложениях погоды и мирового времени, и пишет место не распознано на строке обновлено восклицательный знак в треугольнике.

В чем может быть проблема?

я так понимаю вводили location кириллицей?

нет латинницей, причем при проверке города в приложении пишется "Kovrov Russia"

для проверки, разрешите этому хосту(телефону) ходить в инет напрямую, разрешите ему коннектиться куда угодно и смотрите куда он трафик и на какие порты гоянет.

[dron85]

вопрос с web приложениями снят, прошил телефон новой прошивкой и все заработало.

Остался вопрос с резервированием, файл 46ххsettings настроил. В статусе Avaya MV IPtel вижу что телефон отдает файл backup, но в папке он не появляется. Администратор наш предположил что косяк в разрешениях на запись именно в эту папку, но где ето настроить не понятно (в своиствах папки вкладка безопасность не помогло)

Расскажите по пунктам как это делать, может я что то забыл

Заранее благодарю

[michael_loginov]

вопрос с web приложениями снят, прошил телефон новой прошивкой и все заработало.

Остался вопрос с резервированием, файл 46ххsettings настроил. В статусе Avaya MV IPtel вижу что телефон отдает файл backup, но в папке он не появляется. Администратор наш предположил что косяк в разрешениях на запись именно в эту папку, но где ето настроить не понятно (в своиствах папки вкладка безопасность не помогло)

Расскажите по пунктам как это делать, может я что то забыл

Заранее благодарю

если смотреть внимательно лог то он показывает и путь куда бекап падает + надо смотреть что на дисплее телефона происходит, может ему не удается положить?
вобщем лог MV_IPTEL HTTP и HTPPS бы не помешал

[dron85]

лог Avaya MV IP_Tel

2012-04-17T08:05:32---Checking for BCMS Files on Primary Fileserver
2012-04-17T08:05:32---HTTPS Client --- Certificate validation
2012-04-17T08:05:32---Certificate is self-signed
2012-04-17T08:05:32---GET aborted - file length zero or missing : URL:- https://198.152.254.2:411/BCMSdata/BCMSFiles.list to store at :- C:\Program Files\Avaya\MV_IPTel\data\BCMSdata\BCMSFiles.list
2012-04-17T08:05:32---HTTPS Client --- Certificate validation
2012-04-17T08:05:32---Certificate is self-signed
2012-04-17T08:05:36---HTTP GET request from - 198.152.2.194
2012-04-17T08:05:36---HTTP Server: File NOT found :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\b02d02p2_9.bin"
2012-04-17T08:05:42---HTTP GET request from - 198.152.1.253
2012-04-17T08:05:42---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:05:42---Bytes transferred:- 2970
2012-04-17T08:05:45---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:05:45---HTTP data:- /phonebackup/4025_96xxdata.txt
2012-04-17T08:05:46---HTTP GET request from - 198.152.1.253
2012-04-17T08:05:46---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:05:46---Bytes transferred:- 63824
2012-04-17T08:06:02---HTTP GET request from - 198.152.1.51
2012-04-17T08:06:02---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxupgrade.scr"
2012-04-17T08:06:03---Bytes transferred:- 7002
2012-04-17T08:06:03---HTTP GET request from - 198.152.2.20
2012-04-17T08:06:03---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:06:03---Bytes transferred:- 2970
2012-04-17T08:06:04---HTTP GET request from - 198.152.2.20
2012-04-17T08:06:04---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:06:04---Bytes transferred:- 63824
2012-04-17T08:06:07---HTTP GET request from - 198.152.1.51
2012-04-17T08:06:07---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:06:07---Bytes transferred:- 63824
2012-04-17T08:06:27---HTTP GET request from - 198.152.2.173
2012-04-17T08:06:27---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:06:27---Bytes transferred:- 2970
2012-04-17T08:06:28---HTTP GET request from - 198.152.2.173
2012-04-17T08:06:28---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:06:28---Bytes transferred:- 63824
2012-04-17T08:06:31---HTTP GET request from - 198.152.2.173
2012-04-17T08:06:31---HTTP Server: File NOT found :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\bm32a2_1.hex"
2012-04-17T08:06:49---HTTP GET request from - 198.152.2.26
2012-04-17T08:06:49---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:06:49---Bytes transferred:- 2970
2012-04-17T08:06:50---HTTP GET request from - 198.152.2.26
2012-04-17T08:06:50---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:06:50---Bytes transferred:- 63824
2012-04-17T08:07:43---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:07:43---HTTP data:- /phonebackup/4381_96xxdata.txt
2012-04-17T08:08:10---HTTP GET request from - 198.152.2.35
2012-04-17T08:08:10---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:08:10---Bytes transferred:- 2970
2012-04-17T08:08:11---HTTP GET request from - 198.152.2.35
2012-04-17T08:08:11---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:08:11---Bytes transferred:- 63824
2012-04-17T08:08:14---HTTP GET request from - 198.152.2.16
2012-04-17T08:08:14---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:08:14---Bytes transferred:- 2970
2012-04-17T08:08:14---HTTP GET request from - 198.152.2.202
2012-04-17T08:08:14---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:08:14---Bytes transferred:- 2970
2012-04-17T08:08:15---HTTP GET request from - 198.152.2.16
2012-04-17T08:08:15---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:08:15---Bytes transferred:- 63824
2012-04-17T08:08:16---HTTP GET request from - 198.152.2.202
2012-04-17T08:08:16---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:08:16---Bytes transferred:- 63824
2012-04-17T08:08:17---HTTP GET request from - 198.152.2.15
2012-04-17T08:08:17---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:08:17---Bytes transferred:- 2970
2012-04-17T08:08:18---HTTP GET request from - 198.152.2.15
2012-04-17T08:08:18---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:08:18---Bytes transferred:- 63824
2012-04-17T08:08:18---HTTP GET request from - 198.152.2.202
2012-04-17T08:08:18---HTTP Server: File NOT found :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\bm32a2_1.hex"
2012-04-17T08:08:30---HTTP GET request from - 198.152.1.165
2012-04-17T08:08:30---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:08:30---Bytes transferred:- 2970
2012-04-17T08:08:34---HTTP GET request from - 198.152.1.165
2012-04-17T08:08:34---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:08:34---Bytes transferred:- 63824
2012-04-17T08:08:55---HTTP GET request from - 198.152.1.39
2012-04-17T08:08:55---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxupgrade.scr"
2012-04-17T08:08:55---Bytes transferred:- 7002
2012-04-17T08:08:59---HTTP GET request from - 198.152.1.39
2012-04-17T08:09:00---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:09:00---Bytes transferred:- 63824
2012-04-17T08:09:09---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:09:09---HTTP data:- /phonebackup/1069_96xxdata.txt
2012-04-17T08:09:15---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:09:15---HTTP data:- /phonebackup/1069_96xxdata.txt
2012-04-17T08:09:25---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:09:25---HTTP data:- /phonebackup/1069_96xxdata.txt
2012-04-17T08:09:51---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:09:51---HTTP data:- /phonebackup/1069_96xxdata.txt
2012-04-17T08:10:44---HTTP GET request from - 198.152.2.21
2012-04-17T08:10:44---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\16xxupgrade.txt"
2012-04-17T08:10:44---Bytes transferred:- 2970
2012-04-17T08:10:45---HTTP GET request from - 198.152.2.21
2012-04-17T08:10:45---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:10:45---Bytes transferred:- 63824
2012-04-17T08:10:48---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:10:48---HTTP data:- /phonebackup/1100_96xxdata.txt
2012-04-17T08:10:48---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:10:48---HTTP data:- /phonebackup/1100_96xxdata.txt
2012-04-17T08:10:48---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:10:48---HTTP data:- /phonebackup/4025_96xxdata.txt
2012-04-17T08:11:11---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:11:11---HTTP data:- /phonebackup/4025_96xxdata.txt
2012-04-17T08:11:16---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:11:16---HTTP data:- /phonebackup/4381_96xxdata.txt
2012-04-17T08:11:49---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:11:49---HTTP data:- /phonebackup/4381_96xxdata.txt
2012-04-17T08:12:02---HTTP GET request from - 198.152.1.110
2012-04-17T08:12:02---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxupgrade.scr"
2012-04-17T08:12:02---Bytes transferred:- 7002
2012-04-17T08:12:06---HTTP GET request from - 198.152.1.110
2012-04-17T08:12:06---HTTP Server: File requested :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\46xxsettings.txt"
2012-04-17T08:12:06---Bytes transferred:- 63824
2012-04-17T08:12:11---HTTP GET request from - 198.152.1.110
2012-04-17T08:12:11---HTTP Server: File NOT found :- "C:\Program Files\Avaya\MV_IPTel\data\HTTPdata\b20d01b2_9.bin"
2012-04-17T08:12:24---HTTP Other Command:- PUT ; HTTP Version:- HTTP/1.1
2012-04-17T08:12:24---HTTP data:- /phonebackup/4381_96xxdata.txt

[Pterodahtil]

Подниму тему.
У кого-нибудь получилось бекапить настройки телефонов с помощью IpTel?
У меня 16хх и 96х1 не могут положить файл.

[michael_loginov]

Подниму тему.
У кого-нибудь получилось бекапить настройки телефонов с помощью IpTel?
У меня 16хх и 96х1 не могут положить файл.

У меня 1608 настройки бекапили свои без проблем.